← BACK TO BLOG

What Do SMPTE Color Bars Mean? Each Part of the TV Test Pattern

SMPTE color bars are the TV test pattern of seven bars over a thin strip of color patches and a dark bottom row. Engineers compared the bars as received with the known signal to see what a tape or link had changed. CBS Technology Center added the strip and black-level patches in 1977, and SMPTE published the pattern in 1978.

BeamTracer's Color Bars card in Title Cards is drawn for BeamTracer on the same structure: a row of bars, a reverse row under it and a bottom row of gray steps or color blocks, at proportions you set. Put your channel name on a plate across it for an intro or a break. It is a picture for video, not a calibrated test signal, and it has no reference tone yet.

Who made SMPTE color bars, and why?

Color bars began at RCA, and CBS turned them into the SMPTE pattern. RCA engineers Norbert D. Larky and David D. Holmes filed a patent for an electronic color test pattern generator in April 1951, and it was granted in April 1956 (US 2,742,525). According to a 2005 letter from Holmes that his son shared with VideoUniversity, he built the first generator because the test signals then made from scanned slides were too noisy, and it took about fifty vacuum tubes.

From U.S. Patent 2,742,525, N. D. Larky and D. D. Holmes, RCA, filed 1951. Excerpted by algocu, public domain, via Wikimedia Commons.

By the 1970s, U.S. studios aligned color monitors with split-field bars defined in the EIA standard RS-189-A. In 1975, CBS Technology Center in Stamford, Connecticut, began studying how studio picture monitors drift. A. A. Goldberg described the answer in a paper for the National Association of Broadcasters' 1977 engineering conference (NAB Proceedings, pages 84 to 85). "Color monitors drift with time and require periodic checking," Goldberg wrote, usually before each show. CBS added a thin strip of color patches under the existing bars and two patches near black, so hue, saturation and black level could be set by eye without instruments. Goldberg reported that the signal had run for six months at the CBS Television Network's New York facilities. CBS submitted it to SMPTE's video technology committee and chose not to patent it, which put it in the public domain.

SMPTE published the pattern as ECR 1-1978 and revised it in 1990 as Engineering Guideline EG 1-1990 (SMPTE document registry). Radio World's 2021 obituary of CBS engineer Hank Mahler credits him with developing the bars.

What does each part of SMPTE color bars check?

Each part of the pattern checks one setting, so a technician reads it from the top down.

SMPTE color bars in the ECR 1-1978 layout. Rendition by Denelson83, public domain, via Wikimedia Commons.

  • The seven top bars are gray, yellow, cyan, green, magenta, red and blue: every mix of red, green and blue with at least one of them on, in order of falling brightness. On a waveform monitor they step down like a staircase, and on a vectorscope each lands in its own target box (Tektronix NTSC measurement primer).
  • The thin strip under them is the CBS addition. Blue sits under gray, magenta under cyan, cyan under magenta and gray under blue, with black under the other three. With the monitor showing blue only, four bars light, and each sits directly over the patch it should match (Goldberg, 1977).
  • The bottom row holds a -I patch, a 100% white square, a +Q patch and the PLUGE. The white square is a 100% reference for checking overall level, since the gray bar above is only 75% (Tektronix). According to Wikipedia's article on the bars, the -I and +Q patches draw two short lines on a vectorscope's I and Q axes, which checks that the receiver decodes color correctly.
  • PLUGE stands for picture line-up generation equipment. In a black surround at 7.5 IRE sit a patch a little darker than black (3.5 IRE) and one a little lighter (11.5 IRE) (Goldberg, 1977; Tektronix FAQ, archived).

EBU color bars on a Tektronix waveform monitor and vectorscope. Public domain, via Wikimedia Commons.

Why are SMPTE color bars 75% instead of 100%?

Full-strength bars carry levels that many systems cannot pass without distortion, so Tektronix's NTSC primer recommends 75% bars for basic testing (Tektronix). Its gamut poster shows 100% NTSC bars exceeding a 120 IRE alarm (Tektronix gamut poster).

The ITU names a bar signal with four numbers: white bar level, black level, then the highest and lowest levels in the colored bars. SMPTE's NTSC bars are 75/7.5/75/7.5, the common European EBU bars are 100/0/75/0 (a full white bar with 75% colors), and full-field bars are 100/0/100/0 (ITU-R BT.471). EBU bars are a plain row without the strip or the PLUGE, and according to Wikipedia, test cards such as the Philips PM5544 carry an equivalent set.

How do you set up a monitor with SMPTE color bars?

Set black with the PLUGE, white with the 100% square, then color with the blue strip, feeding bars from a real signal generator or a camera. Tektronix's published procedure runs in this order:

  1. Warm the monitor up in the light it will be used in, and feed it SMPTE bars.
  2. Turn the color (chroma) control all the way down.
  3. Turn brightness until the darker PLUGE patch merges with the black around it and the lighter one is just visible.
  4. Turn contrast up, then back down until the 100% white square just starts to change.
  5. Switch the monitor to blue only, or look through a blue gel.
  6. Set chroma until the gray and blue bars match their patches, then set hue until cyan and magenta match theirs.

When the settings are right, the line between each bar and its patch disappears (Tektronix FAQ, archived). CBS's paper sets saturation before hue because the chroma control moves all four bars (Goldberg, 1977). BeamTracer's card is not a calibrated signal, so use a generator's bars for this.

What is the tone played with color bars?

The tone is a steady 1,000 Hz sine wave at a reference level, sent with the bars so the sound can be lined up too. The pair is known as bars and tone (Duke University Libraries). In North America the reference is −20 dBFS, the level in SMPTE RP 155 (SMPTE document registry). European broadcasters align 18 dB below full scale, −18 dBFS, under EBU R68 (EBU R68).

Bars and tone sat at the head of program tapes so each playback machine could be adjusted before the show. PBS's 2015 rules give a typical leader: 60 seconds of SMPTE RP 219 bars with tone at −20 dBFS and 1 kHz, a 20-second slate, a countdown from 10 with a one-frame 400 Hz beep each second, 2 as the last number, then black until the program (PBS Technical Operating Specification). File delivery has dropped the habit: PBS Distribution's 2025 rules ask for a 15-second slate and say not to put bars and tone before it (PBS Distribution).

What do HD color bars add?

HD bars put the SMPTE pattern inside a 16:9 frame, so one signal works for HD and, cut down to 4:3, for SD. Japan's Association of Radio Industries and Businesses established the design as ARIB STD-B28 on December 14, 2000, and SMPTE adopted it as RP 219:2002 (ARIB STD-B28).

The 4:3 middle holds 75% bars with 40% gray at the sides. Under them sit 100% cyan and 100% blue, then a row with 100% yellow and red around a luminance ramp that exposes digital bit errors, then a bottom row with a 100% white block and a PLUGE in 2% steps. HD monitors are set with the -2% and +2% patches, SD monitors with +2% and +4%. ARIB also offers a +I patch, because skin tones fall near the +I axis on an NTSC vectorscope.

Are color bars still used?

Yes, in engineering. PBS still required 60 seconds of HD bars on program tapes in 2015, and Tektronix's 2012 gamut poster uses color bars to check digital HD signals (Tektronix gamut poster). NewTek's Video Toaster put SMPTE bars on its Preview monitor at startup. For the black-and-white pattern that came before color, see the RCA Indian-head test pattern, and for every card in the family, how to make a retro TV test card.

How do I make a color bars card with my own channel name?

Open BeamTracer Title Cards, choose the Color Bars module and the 75% CLASSIC preset, then turn on the ident plate and type your channel name. Every bar color, row height and bar count can be changed, and the card renders as a video for an intro, a break or a stream overlay.

  1. Open Title Cards and choose MODULE → COLOR BARS.
  2. Under PRESETS, choose 75% CLASSIC for seven bars over a reverse row and a gray ramp, or 100% FULL for eight full-strength bars.
  3. Under LAYOUT, set BAR ROW HEIGHT and REVERSE ROW HEIGHT, and choose BOTTOM ROW → RAMP or BLOCKS.
  4. Turn on TEXT → IDENT PLATE and type your channel name.
  5. Under STYLE, choose a PLATE COLOR, and change any bar's color from BAR 1 onward.
  6. Choose RENDER, then RENDER VIDEO, and SAVE VIDEO when it reads VIDEO READY.

The guide covers each step, the ident plate and every setting. With HUE at 0, SATURATION and CONTRAST at 100% and GAMMA at 1, every pixel is exactly the color you set (Good to know). The WE’LL BE RIGHT BACK preset is a ready break card, and AUDIO-REACTIVE, in the clip below on BeamTracer's own card, moves the bars with the music (how to make TV color bars move to music).

BeamTracer is not affiliated with or endorsed by SMPTE, CBS, RCA, ARIB, the EBU, Tektronix or PBS.

Get BeamTracer updates by email

Email me

At most one email a day and three a week across both. No spam. Unsubscribe anytime.

We email a link to confirm first. Every email has an unsubscribe link. See our Privacy Policy.