How Do I Turn Geometric Motion Graphics Into ILDA?
Open Video to Laser in CONVERT, load a short clip with light strokes on a dark background, and start with SVG PARSER and TRACE MODE → CENTER. Compare the same corners and lines across the preview panes, then convert and play the animation in ILDA Viewer.
The converted NOT A MOON example, replayed in Cinema’s software preview.
What settings should I use for thin geometric lines?
Open VIDEO → LASER → CONVERT and click NOT A MOON. Let the source frames load. The sample applies its own settings, so verify the values below in CLASSIC before you start. For your own file, start with a short MP4 or WebM of light strokes on a dark background.
| Where | Setting for NOT A MOON |
|---|---|
| CONVERSION METHOD | SVG PARSER |
| DETAIL LEVEL | HIGH, SIMPLIFY 2.0, TRACE MODE → CENTER |
| PROCESSING | THRESHOLD 11, SMOOTHING OFF, INVERT COLORS off |
| ANIMATION | TARGET FPS 10, POV (BLUR) 4, FRAME CONTEXT on |
On thin white line art, CENTER traces along the middle of the stroke. POV (BLUR) distributes parts of a source picture across successive output frames. At 10 FPS with POV set to 4, you can see fewer source poses each second even though ILDA playback still runs at 10 FPS. If fast movement is more important than keeping a dense picture readable, use POV (BLUR) 1 as a comparison and check the resulting point load.
How do I pick the best trace for my clip?
Move beyond the sparse opening. Scrub to a frame where the targeting graphic fills the screen. Hold the scrubber there and find the same detail in Original, Bitmap Tracer, and SVG Parser. Follow a long straight stroke into a bracket corner. Check where the corner meets the next line and where the circle closes. Check one earlier and one later frame too. An isolated clean frame can hide a corner that disappears as the graphic moves.
In the example, the SVG Parser pane keeps more of the thin, continuous geometry than the bitmap trace. Try IMAGETRACER if your own clip has soft or irregular edges. Compare the same frame again before committing to a conversion.
How do I check the animation before I download the ILDA file?
Convert the clip and play the busy section in ILDA Viewer. Watch the lines through several poses, then check the point load on the worst frame.
- Click CONVERT and wait for Conversion Complete. Read the messages about the result. This run reported 123 source frames and 489 ILDA frames, with the full offline trace retained. Counts depend on the clip and settings.
- Click OPEN VIEWER. Inspect the clip in 2D before switching to 3D. Pause on a busy frame, then play through the same section you compared in Convert. Watch for disappearing brackets, doubled strokes, or bright specks that show up for one frame.
- In 3D → SCENE → BEAM MODE, choose Cinema — Premium fog for the software beam preview.
- Set Camera Preset to Orbit Mode in the viewer toolbar to see the beams from another angle.
- Review POINT BUDGET in Convert with the intended point rate, especially on the busiest frames.
- Click DOWNLOAD ILD in Convert to save the animation as an ILDA file.
Why do lines disappear or flicker after conversion?
| What you see | What to change first |
|---|---|
| Grain and glow become extra lines | Raise THRESHOLD a little and compare the same frame. If the glow and the important strokes are close in brightness, go back to the source and reduce the glow. |
| Thin lines disappear | Try a small decrease from THRESHOLD 11. If lowering it introduces clutter, give the missing strokes more contrast in the source. |
| The shape looks rounded or too sparse | Check SIMPLIFY and DETAIL LEVEL before touching frame rate. Lower simplification a little and look at the same bracket corner again. |
| The preview looks clean, but playback flickers | Confirm FRAME CONTEXT is on, convert again, and judge the output in the Viewer. The panes in Convert trace individual source frames. |
| Busy frames are over the selected point rate | Remove small decorative lines from the source or increase SIMPLIFY slightly. Reconvert, check that the main outline survived, and review POINT BUDGET again. |
See the Video to Laser guide for the full controls and the Frame Context tutorial for an on-and-off comparison.