← BACK TO BLOG

How Do I Add an Animated Comic Burst Behind a Person?

To add an animated comic burst behind a person, open BeamTracer Performer, load a video and add LIGHT RAYS. Choose STYLE → BURST to draw changing radial wedges. BEHIND PERSON turns on with the style, keeping the person in front. Adjust the fan, then render an MP4 or WebM.

BeamTracer handles the person cutout and the animated fan in one effect. You can try a different ray count or color while the clip keeps playing, without drawing wedges or keyframing a separate mask around the person. Use the effect for a reaction shot or performer introduction where the face needs to stay readable.

What is a comic burst, and is it the same as anime speed lines?

A comic burst is a fan of flat wedges spreading from a chosen point. The rays give a subject a sudden, emphatic backdrop, much like the radial lines in an anime impact frame. BeamTracer's BURST changes the arrangement of those wedges over time; the person continues moving normally in front.

The fan snaps to new shapes instead of spinning continuously. Some rays use TINT, while others are dark or pale. Gaps between the rays still show the original video background. This recipe makes a flat graphic burst; a camera flying through a three-dimensional speed tunnel is a different effect.

Use a small ray count for broad poster-like wedges. More rays make a denser, busier background. A held reaction shot can carry a few large rays; a fast performance cut may suit a tighter fan.

How do I put the burst behind a moving person?

Choose BURST and leave BEHIND PERSON → ON. BeamTracer uses its person mask to preserve the foreground while drawing the burst over the background. Try the included TRINA · HANDS example before loading your own clip so you can check the effect with a known source.

  1. Open Performer and open FX RACK.
  2. Under VISUAL SOURCE, choose TRINA · HANDS, or use VIDEO · IMAGE to load a video that shows a person clearly.
  3. Add or select LIGHT RAYS, then choose STYLE → BURST.
  4. Set RAYS to 22, RESHAPE to 4, CENTER X to 0.50 and CENTER Y to 0.30.
  5. Set INTENSITY to 1.00, TINT to #ffd447, and check BEHIND PERSON → ON.
  6. For an uploaded video, choose RENDER → MP4 · H.264 or WEBM · VP9 → RENDER VIDEO → SAVE VIDEO.

Wait for the mask to settle before judging the first frames. Watch the outline of the head, shoulders and raised hands through several poses. The rays should stop at the person, while their arrangement changes in the surrounding background. A good still frame alone cannot tell you whether fast-moving fingers stay in front.

The comic sunburst guide has the full effect reference. The tracking and masks guide covers other ways to confine effects to a subject.

The center and the mask do different jobs

BEHIND PERSON follows the person mask. CENTER X and CENTER Y place the fan's fixed origin in the frame. Moving your head does not automatically move that origin with it.

Which settings make broad comic rays instead of a busy fan?

Lower RAYS to 8 and RESHAPE to 1 for a few broad wedges that hold longer. Keep the center and intensity unchanged so you can see what those two controls contribute.

ControlOpening recipeBroad-ray variationWhat to watch
RAYS228The number of ray positions around the center
RESHAPE41How often timed changes rearrange the fan
TINT#ffd447#ff9f45The main ray color; dark and pale rays remain
CENTER X / Y0.50 / 0.300.50 / 0.30The origin stays in the same place
INTENSITY1.001.00Solid graphic rays
BEHIND PERSONONONThe foreground remains the original person

Lower INTENSITY if you want more of the room to show through. At 1.00, the colored wedges are already solid in this style. Judge the result at the size you will post: fine rays that look attractive on a large monitor can become distracting behind a small face.

How do I move the burst to one side of the frame?

Change CENTER X and CENTER Y to reposition the fan without moving or cropping the source video. Try CENTER X 0.20, CENTER Y 0.45, RAYS 32, RESHAPE 2 and TINT #54e6ff for a denser cyan fan spreading from the left side.

An off-center origin is useful when your subject stands to one side or the composition needs space for a caption. Place the origin first, then decide how many rays the remaining background can carry. Check a few poses with arms extended; a center that works around a close-up face may look awkward once the whole gesture comes into view.

Keep the source framing consistent while comparing these settings. Changing the video's fit and the fan's center together makes it harder to tell which adjustment improved the composition.

Can the burst change on the beat or when I press a button?

Yes. A detected beat or HIT gives BURST a new fan in addition to its timed RESHAPE changes. Lower RESHAPE when you want the music or your manual hits to be easier to distinguish.

Set RESHAPE to 0 to stop scheduled changes, then press HIT on the LIGHT RAYS effect. The source video keeps moving while the fan holds between hits. A playing track can still trigger beat changes, so pause the track when checking manual-only behavior. Press HIT to accent a lyric or gesture when a continuously changing background would distract from the performance.

Use the modulation guide when you want to route a continuous control. Keep the first experiment simple: confirm the fan changes when you press HIT before adding more modulation.

Why are rays covering the face, or missing around the hands?

Check BEHIND PERSON first, then inspect the source and mask over time. With the switch off, the rays are allowed across the person. With the switch on, a difficult foreground edge can still need a clearer source.

ProblemAdjustment or check
Rays run across the faceConfirm BEHIND PERSON → ON on LIGHT RAYS
The effect looks like hazeChoose STYLE → BURST, not SHAFTS
Hands briefly disappear into the backgroundTry slower gestures and clearer lighting; inspect the moving mask rather than one still
The background is too busyReduce RAYS and RESHAPE, then check the face at phone size
The whole room is still visible between wedgesGaps are part of the burst design; the effect is not a full background replacement
The fan changes more often than RESHAPE suggestsA playing track's beats and HIT can add changes

Check the moving outline

Review a moment with hands raised and another with arms crossing the body. Those poses reveal foreground problems that a centered, still face can hide.

How do I save the effect for a video or live camera?

Use RENDER for an uploaded video and RECORD for a live camera performance. An uploaded clip gives you a repeatable source, which is helpful when comparing settings and checking the finished motion.

For a video, choose the output's aspect ratio and resolution in RENDER, select MP4 · H.264 or WEBM · VP9, then use RENDER VIDEO and SAVE VIDEO. Keep INCLUDE AUDIO off for a silent graphic loop or on when the clip needs sound. The export guide explains the uploaded-video workflow and current export access.

For a camera, select CAMERA under VISUAL SOURCE, confirm the mask and composition in the live preview, and press RECORD. Perform your take, then press STOP. Check the saved take through a raised-hand gesture and a background change before using the effect in a longer performance.

Get BeamTracer updates by email

Email me

At most one email a day and three a week across both. No spam. Unsubscribe anytime.

We email a link to confirm first. Every email has an unsubscribe link. See our Privacy Policy.