How Do I Make a Stranger Things Title Opening?
To make a Stranger Things title opening, open BeamTracer Title Cards, choose UPSIDE-DOWN TITLE under MODULE, and type STRANGER and THINGS as the two words. It plays as a slow film-style opening: close shots of single letters with a credit over each, then the letters drift together as the camera pulls back. Use RENDER to save it as a video.
The clip and the still below are BeamTracer's own output, rendered with RENDER VIDEO from the CLASSIC RED preset with STRANGER and THINGS typed in. Both words are set in ITC Benguiat, the commercial typeface used for the show's title. We license it, but BeamTracer doesn't include it. If you own it, add it with the steps below to get this exact look.
BeamTracer is not affiliated with or endorsed by Stranger Things or its makers.
What does the Upside-Down Title opening do?
The opening runs about 45 seconds at the default settings. A credit appears alone on black. Five close shots follow, each filling the frame with part of a letter while the next credit fades up through red. A closer shot of the serifs comes next. Then the camera pulls back from about six and a half times closer while each letter slides home on its own path, and the bars grow out at the end. The title holds briefly and fades to black.
Each part has its own control under MOTION. FRAGMENTS sets how long the close shots run, and FRAGMENT CUTS sets how many there are. LETTERS ASSEMBLE times the slide into place, PULL-BACK sets how near the camera starts, and FADE AWAY off holds the title on screen instead of fading it out. Type your own credits under TEXT → SHOT CREDITS, one credit a line, or turn SHOT CREDITS off for a bare opening.
How do I get this exact look with my own licensed font?
If you own ITC Benguiat, or another face you have the right to use, add it from the font list itself. These are the settings used for the renders on this page:
- Open Title Cards, choose UPSIDE-DOWN TITLE under MODULE, and pick the CLASSIC RED preset.
- Open TEXT → TOP WORD and type STRANGER in TOP WORD TEXT. Open TEXT → BOTTOM WORD and type THINGS in BOTTOM WORD TEXT.
- Click the TOP WORD FONT list and press ADD YOUR FONT. Choose your OTF, TTF, WOFF or WOFF2 file. The font is added under YOUR FONTS and selected for the top word.
- Click BOTTOM WORD FONT and choose the same font under YOUR FONTS.
- Set TOP WORD SIZE and BOTTOM WORD SIZE to 19.6%, and TOP WORD LETTER WIDTH and BOTTOM WORD LETTER WIDTH to 73%.
- Set TOP WORD TRACKING to 3% and BOTTOM WORD TRACKING to 6%, then render the opening to check it (below).
The font list shows each face with your own word in it, so you can compare faces before you choose one. A font you add appears under YOUR FONTS with the name stored in the file, marked YOURS, in every font list in BeamTracer.
The letter widths and tracking above suit ITC Benguiat. With another face, start from the same numbers. Adjust the two LETTER WIDTH sliders until the words are about the same width, then the TRACKING sliders until the letters stop touching.
Use a font you own
Only add a font file you have the right to use. ITC Benguiat is a commercial typeface. Buy a license from its foundry or an authorized reseller, and check that the license covers the videos you plan to publish.
What will the opening look like without a licensed font?
BeamTracer sets the Upside-Down Title in DOMINE BOLD, a free serif, so you can use the preset without buying anything. The preset also starts with its own words, KEPLER and STREET, until you type yours. The shots, glow, bars and timing are the same, but the default letters are heavier and squarer, so the default preview will not look like the renders at the top of this page.
This is the same moment of the same opening, with only the words changed from the defaults. The bars, glow and red ink match. The slab serifs are blockier, and at the default tracking the letters overlap slightly.
If you don't have a licensed face, try the other faces in the TOP WORD FONT list, including the serifs in the font library, and adjust the LETTER WIDTH and TRACKING sliders for each one.
How do I save the opening as a video?
Use RENDER at the top of the app. It draws every frame of the video, so the slow pull-back has no dropped frames even when the preview stutters.
- Click RENDER, open RENDER RANGE, and check RENDER A SELECTED RANGE.
- Set START (SECONDS) to 0 and LENGTH (SECONDS) to 47 to capture the whole opening and its fade.
- Choose 16:9, 1080P or 4K, and 24 under FRAME RATE for a film cadence.
- Choose MP4 · H.264 or WEBM · VP9, then click RENDER VIDEO.
- When the render finishes, click SAVE VIDEO.
A render always starts the opening from its first frame. Leave INCLUDE AUDIO checked to keep the selected music, or uncheck it for a silent file you can score in your editor.
Your font and settings stay in this browser. To render on another computer, add the font file there as well.
To put the title over your own footage instead of black, open BACKGROUND and choose CHROMA GREEN or CHROMA BLUE, then key out the color in your editor.